Autoclave & Sterilizer Service
MedServ also services tabletop autoclaves directly.
MedServ services exam chairs, exam tables and procedure chairs directly for medical and outpatient practices in Tampa Bay and across Florida. Tell us the make, model and what the chair is doing, and we will confirm whether we can service it and when.
A powered chair stuck halfway up, or a table that will not hold its position, takes an exam room out of the schedule. MedServ services exam chairs and tables directly, so your practice has one contact for the repair, the follow-up and the record of what was done.
Many practices we talk to use Midmark and Ritter tables and chairs, both manual and powered. Coverage is confirmed unit by unit: the manufacturer, model, serial number, controls, accessories, condition and parts availability decide whether we can take the work. If a chair falls outside what we service, we tell you so rather than guess.
Every visit is logged against that chair or table in the MedServ platform, by room and location: the reported problem, what was found, parts, estimates, return visits and the next inspection date.
Describe what staff can see without forcing the chair or removing covers. We confirm the cause and the fix once it has been assessed.
Height, back, tilt or foot-section movement that stops, stalls or moves only one way.
Controls that do not respond, respond intermittently or move the wrong function.
A chair that creeps down, will not hold position, grinds or knocks. Take it out of use until it is checked.
Torn tops, loose rails, stirrups, steps, drawers and paper holders. We confirm what we can handle for your model.
Scheduled checks based on the manufacturer’s guidance for your model, with findings and the next due date recorded.
Quotes for parts and repairs, and a straight answer when an older chair is no longer worth repairing.
A few notes from the exam room usually shortens the visit. Staff do not need to troubleshoot the chair, and should not force it into position, remove covers or test it with a patient on it.
If other chairs or tables in the practice are due for inspection, mention them. Grouping units into one visit means fewer interruptions to the schedule.
Call or send a service request with the make, model, serial number if you have it, the room and location, and what it is doing. A photo of the label and a short video of the problem save time.
We confirm whether we can service that unit, the likely scope, timing and any charges before work goes ahead, and schedule around patient hours where we can. Parts and repair estimates are shared with you for approval.
MedServ completes the work and records the findings, parts and any follow-up visit against the chair, along with the next inspection date.
MedServ is based in Tampa Bay and works with medical practices across Florida. Scheduling and travel depend on where the equipment is, so we confirm timing for each request rather than promising a fixed response window.
Practices with several exam rooms or locations can keep every chair and table on one inspection schedule and one service record, with the same contact for requests at each site.
MedServ services the chair or table itself: inspection, troubleshooting, repair, parts and the service record. Coverage is confirmed for each make, model and serial number, and listing a manufacturer here does not mean every model is covered or that MedServ is an authorized dealer.
Your practice decides when a chair is taken out of use and when it goes back into patient care. If a chair moves unexpectedly, will not hold its position or shows electrical damage, stop using it, keep patients off it and contact us.
MedServ services exam chairs and tables directly. If a specific unit needs manufacturer-only work or a part only the manufacturer supplies, we tell you that and coordinate the next step.
We commonly see Midmark and Ritter exam tables, exam chairs and procedure chairs. Coverage is confirmed for each make, model and serial number, so send those details with your request and we will tell you whether we can service the unit.
Most chair and table work is done in the exam room. If a repair needs a part on order or a return visit, we schedule it and record it against the chair.
The make, model and serial number from the label, the room and practice location, what the chair is doing, which control you were using, and whether it has been taken out of use. A photo or short video helps.
Follow the manufacturer’s guidance for your model and how heavily the room is used. We record an inspection interval for each chair and the next due date so it is not missed.
We will tell you what is and is not available for that model and give you a straight comparison of repair against replacement. MedServ can also help plan a replacement as part of an exam-room project.
Send the make, model and what it is doing. We will confirm whether we can service it and when.